冰冻血浆解冻箱干式溶浆机旌派公司生产制造氮吹仪血液溶浆机 冰冻血浆解冻箱 找冰冻血浆解冻箱 这里有冰冻血浆解冻箱 冰冻血浆解冻箱医院采购 血浆解冻箱 血液冰冻解冻箱 血浆化浆机 血浆解冻箱,血浆解冻箱
产品说明：
JipadJipad-6GL干式血液溶浆机利用隔水膜袋“隔水解冻”，完全实现了血浆干式解冻的目的,解冻结束:“血浆外观干燥，透明、无水渍，污物，标签不会模糊、脱落”。特制热交换系统能够达到“快速解冻”的效果。专门设计的“摇匀系统”避免血浆内纤维蛋白凝结。“返回水设计”有利融化箱内水温恒定无热点。
Jipad-6GL干式血液溶浆机结构合理，紧凑，零部件经老化等特殊处理，性能稳定可靠，整机使用寿命长，不同型号的产品适合不同规模的医院输血科，血库使用，并经多家医院临床验证。
产品特点:
1. Jipad-6GL干式血液溶浆机采用美国DS18B20和双金属片两级温控系统，超温自动报警并切断电源。解冻时间20分钟±2分钟。
2.专门设计的的“摇摆锤击”系统，避免血浆内纤维蛋白析出。“隔水膜袋”用医用绿色新型材料制成，无毒,无味，无毒副作用、使用寿命长。
3.水箱密封，长期不用换水，加入专用消毒剂（氯片）效果更好，节约资源减轻换水负担。
仪器对环境不会有水渍、污物溢出,保护环境和操作人员。
4.如有血浆袋破裂因有隔水膜袋包裹，不会造成过量渗漏，污染水箱及环境.
技术参数：
1.电源电压：220V/50HZ
2.功率：1800W
3.可调温度：30℃－－-41℃<±1℃
4.解冻袋数：1-6袋（50-200毫升血浆）
5.解冻时间：10-20min±2min
6.容量：*多12袋（200毫升血浆）
7.可调时间：1min－－99.00min
8.仪器重量：29kg加水：45kg
9.外形尺寸：460X610X960(mm)
10.摇摆频率：50次/分钟
11.循环能力：40L
装 机 方 法：
1、将压水棒放入隔水膜袋中
2、打开仪器上面小盖、加入干净的自来水，是纯净水。（仪器可长期不用换水。使用一段时间后，在仪器工作时，提起隔水膜袋观察水的清澈程度确定是否需要换水）
3、加水时请注意观察蜂鸣报警声停止，停止说明水位已加满请停止加水，过多加水，仪器左侧溢水口，会有水溢出。
4、加水过多时侧面会有水溢出，这样不会影响仪器使用，您可在侧面放水阀门放出少许即可。
5、等待40-50分钟显示屏实际温度显示37度，即可将血浆放入隔水膜袋中点击“开/关”按钮－－－－－－-OK。
6、如需要改变设定温度、时间请参照操作手册。
一．目的
建立循环水浴箱解冻新鲜冰冻血浆、普通冰冻血浆及冷沉淀标准操作规程,规范冰冻血液成分解冻操作流程,确保血液质量安全。
二． 职责
本科室工作人员应用此操作规程,保证为临床提供安全的血浆。
三．原理
冰冻血浆融化箱采用电气控制原理,新鲜冰冻血浆、普通冰冻血浆及冷沉淀等需要在 37 一 40℃稳定温度条件下，快速解冻防止蛋白成分析出 ,循环水溶箱可以维持稳定温度的水 浴条件，快速、批量觧冻,冰冻血液制品,确保觧冻速度和血液质量。
四．适用范围
适用于循环水浴箱解冻新鲜冰冻血浆、普通冰冻血浆及冷沉淀操作。
五、器材与试剂
1、器材：血库专用融浆机，血浆解冻袋
六、环境条件 温度：20-27℃，温度≤80% 七、操作程序：
1、连接进水管，排水管，接通电源；
2、打开电源开关，按“启动"键，提示“缺水"状态，拧开水龙头开始加水，直至进水完成，“预温"灯亮；
3、设定解冻湿度（一般设定为38℃）及解冻时间（根据解冻血浆数量确定，一般设定在16分钟以上）；
4、待预温完成后，水箱水位上升到工作状态；
5、将血浆或冷沉淀从低温冰箱中取出，去掉包装盒，套上解冻袋，放入解冻槽中，盖好解冻箱盖；
6、解冻完成后，依次将血浆解冻袋取出，将血浆去掉解冻袋后放置室温下待用；
7、如果解冻后的血浆温度己经恢复到室温仍未发出，应该将血浆转移到4℃储血冰箱内待用。
八、注意事项
1、解冻箱应使用独立的三芯插座；
2、解冻箱上水时务必连好排水管，防止加水过量后溢水； 3、发现有破损血浆时需立即换水，并进行清洗
4、要避免血袋标签等物品落入水箱内，以免堵塞水管，致使水循环系统瘫痪；
5、解冻箱长期不用时，应将解冻箱内的水全部排尽。
九、保养与维护
1、解冻箱应每周做清洗保养一次，清洗内外表面；
2、温度校正：每年由计量部门对解冻箱进行一次温度检测，如发现实测温度与显示温度相差0.5℃以上，应对解冻箱进行校正
Product Description:
The Jipad brand Jipad-6L dry blood plasmapheresis machine uses the water separating membrane bag to separate the water ａnd thaw. The purpose of plasma dry thawing is completely realized. The end of thawing is: "the appearance of the plasma is dry, transparent, waterless, dirty, ａnd the label will not be fuzzy ａnd falling off". The special heat exchange system can achieve the effect of "fast thawing". The specially designed "shake up system" avoids fibrin condensation in the plasma. The "return water design" is favorable for the constant water temperature in the melting box without hot spot.
The Jipad-6L dry blood dissolving machine has a reasonable ａnd compact structure. The components are treated by aging ａnd other special treatments. The performance is stable ａnd reliable, ａnd the whole machine has long service life. Different types of products are suitable for different scale hospitals transfusion department, blood bank is used, ａnd is verified by many hospitals.
Product features:
The 1. Jipad-6L dry blood plasma dissolve machine adopts the two level temperature control system of American DS18B20 ａnd bimetallic chip, which can alarm automatically ａnd cut off the power. The thawing time was 20 minutes ａnd 2 minutes.
2. specially designed "swing hammer" system to avoid fibrin precipitation in the plasma. "Water diaphragm bag" is made of new medical green materials, which is non-toxic, tasteless, non-toxic side effects ａnd long service life.
3. water tank is sealed for a long time without changing water. The effect of adding special disinfectant (chlorine tablet) is better, saving resources ａnd reducing the burden of water exchange. The instrument does not have water stains, spillage of dirt, protection of the environment ａnd the operator.
4. if the rupture of a plasma bag is wrapped in a membrane bag, it will not cause excessive leakage ａnd pollute the water tank ａnd the environment.
Technical parameters:
1. power supply voltage: 220V/50HZ
2. power: 1800W
3. adjustable temperature: 30 C －－-41 C < + 1 c
4. the number of thawing bags: 1-6 bags (50-200 ml plasma)
5. thawing time: 10-20min + 2min
6. capacity: a maximum of 12 bags (200 ml of plasma)
7. adjustable time: 1min－－99.00min
8. instrument weight: 29kg adding water: 45kg
9. shape size: 460X610X960 (mm)
10. swing frequency: 50 times / minute
11. cycle ability: 40L
Installation method:
1. Put the water rod in the water - proof bag
2. Open the top of the instrument ａnd add clean tap water. It is best to clean water. (the instrument can not change water for a long time. After working for a period of time, in the work of the instrument, the clarity of water in the water diaphragm bag is raised to determine whether the water is needed for water exchange.
3, when you add water, please observe the stop of the beep alarm, stop indicating that the water level has been filled, stop adding water, add too much water, ａnd the overflow on the left side of the instrument will overflow the water.
4, when the water is overloaded, there will be water overflow, which will not affect the use of the instrument, you can release a little on the side of the water valve.
5, waiting for 40-50 minutes to display the actual temperature of the display 37 degrees, you can put the plasma into the water septum bag ａnd click "open / close" button －－－－－－-OK.
6, if you need to change the setting temperature ａnd time, please refer to the operation manual.
I. purpose
Establish standard operation procedures for circulating frozen water tank, thawing fresh frozen plasma, ordinary frozen plasma ａnd cold precipitation, ａnd standardize the operation process of frozen blood components, so as to ensure the quality ａnd safety of blood.
Two. Responsibilities
The staff in this department use this procedure to ensure the safety of plasma in the clinic.
Three. Principle
Frozen plasma melting box adopts the principle of electrical control, fresh frozen plasma, ordinary frozen plasma need to be in a stable temperature 37 to 40 DEG C, rapid thawing to prevent protein precipitation, circulating water soluble box can maintain stable temperature of water bath, fast ａnd batch frozen frozen blood products, explanation, to ensure that the explanation of freezing the speed ａnd quality of blood.
Four. Scope of application
It is suitable for the defrosting of fresh frozen plasma, common frozen plasma ａnd cold precipitation.
Five, equipment ａnd reagents
1. Equipment: a special thawing machine for blood bank, a plasma thawing bag
Six, the environmental conditions of temperature: 20-27 degrees, the temperature is less than or equal to 80%, seven operating procedures:
1, connect the inlet pipe, drain pipe, connect the power supply;
2, open the power switch, press "start" key, prompt "water shortage" state, turn off the faucet start adding water, until the water is completed, "pre temperature" light;
3, set the thawing humidity (generally set to 38) ａnd thawing time (according to the number of thawing plasma is determined, generally set at more than 16 minutes);
4. When the temperature is finished, the water level of the water tank rises to the working state.
5. Remove the plasma or cold precipitation from the cryogenic refrigerator, remove the packing box, set the thawing bag, put it in the thawing tank, ａnd cover the thawing box cover.
6. After the defrosting is completed, the plasma thawing bag is taken out in turn, ａnd the plasma is removed after the defrosting bag is placed at room temperature.
7, if the plasma temperature after thawing has not been released to room temperature, the plasma should be transferred to 4 centigrade to be used in the blood storage refrigerator.
Eight. Precautions
1. An independent three core socket should be used in the thawing box.
2, when the thawing box is on the water, be sure to connect the drain pipe to prevent overflowing water. 3, when the damaged plasma is found, water should be changed immediately ａnd cleaned.
4, to avoid the blood bag label ａnd other articles fall into the water tank, so as to avoid blocking the water pipe, causing the water circulation system to be paralyzed.
5. When the thawing box is not used for a long time, all the water in the thawing box should be exhausted.
Nine, maintenance ａnd maintenance
1, the thawing box should be cleaned ａnd maintained once a week, ａnd the inside ａnd outside surface should be cleaned.
2, temperature correction: once a year, the temperature measurement of the thawing box is carried out by the Metrology Department. If we find the difference between the measured temperature ａnd the display temperature is more than 0.5 degrees, we should adjust the thawing box.
解决实验室工作难题 上海旌派奉上诚意之作
我们都知道实验室样品处理、破碎是实验室工作中的难题，许多科研工作者也因为这两大难题不胜其烦。大批量样品的浓缩或制备时温度控制却怎么也不准确？进行细胞粉碎时总是达不到想要的效果？类似这样的吐槽经常出现在实验室工作人员的口中，而这些问题要如何改善呢？
众所周知，实验室工作离不开科学仪器的帮助，在我国科学仪器领域有着这样一家企业，他的产品系列覆盖了实验室样品处理、破碎、恒温等各个方面，并在国防、物理、化学、生物工程、医药卫生、生命科学、环境工程、高等院校、科研机构等领域得到了广泛应用——他就是上海旌派仪器有限公司。近期，为解决用户实验室样品处理、破碎两大难题，上海旌派仪器有限公司（以下简称上海旌派）特别推出新款台式超声波细胞粉碎机和干式氮吹仪。
台式超声波细胞粉碎机是一款广泛应用于多种动植物、病毒、细胞、细菌及组织破碎的仪器，同时可用来乳化、分立、匀化、提取、消泡、清晰、纳米材料的制备、分散及加速化学反应等实验。上海旌派*新推出的台式超声波细胞粉碎机来自其旗下自主Jipad，而上海旌派Jipad系列产品，向来是以“高自动化、高配置、高性能”著称于国内市场。
这款Jipad台式超声波细胞粉碎机的质量自然也秉持“高自动化、高配置、高性能”的理念：自动调节的超声功率和振幅及工作时间让我们看到了仪器的高自动化；进口钛合金材质超声探头＋特殊隔音材料做到了高配置；微机控制＋高能效换能器则确保了仪器的高性能。笔者认为，拥有这三大优势的Jipad台式超声波细胞粉碎机将是于生物化学、微生物学、药物化学、表面化学、物理学、动物学、农学、医学、制药领域科研机构及企业工作的好帮手。
氮吹仪的主要作用是将氮气吹入加热样品的表面，使样品中的溶剂快速蒸发、分离，从而达到样品无氧浓缩的目的，保持样品更纯净。上海旌派另一款Jipad氮吹仪除了氮吹仪的基本功能之外，在产品细节上做出了改进加强了自动化性能，让仪器操作简单、省时省力，将是农残分析、商检、食品、环境、制药、生物制品等行业样品制备的必备仪器。
特点与优势：
1、 吹针相互独立，避免引起交叉污染。
2、气腔高度可以调节，标准气针长度为150mm。
3、Jipad氮吹仪有12、24个气道控制开关，不浪费气体。
4、在浓缩有毒溶剂时，整个系统可置于通风柜中。
5、内置超温保护装置，自动故障检测及报警功能。
6、LED显示屏，温度同步显示、时间递减显示，操作简单方便。
有了上海旌派Jipad新款台式超声波细胞粉碎机和干式氮吹仪，实验室样品处理、破碎将变得简单方便。如果您想了解更多实验室仪器以及上海旌派的产品信息，可以点击下方链接，更多更全面的信息将呈现在你眼前。
【关于上海旌派仪器有限公司】
上海旌派仪器有限公司(Shanghai Jipad Instrument Co.,Ltd）坐落于上海市浦江镇高科技园区漕河泾开发区，是一家从事恒温设备、样品前处理、实验常规配套设备开发设计、制造、经营销售的技术企业，被评为上海市级优秀企业。拥有产品研发团队和一支技能有素、实践经验丰富的高级技师组成的生产团队，为能制造出性能优良、质量可靠的产品奠定了坚实的基础。
公司拥有国内一流自主Jipad，并在产品研发、生产、调试、检验、试验等每一个生产环节都严格贯彻ISO9001：2000质量体系指令。多年来，公司产品广泛服务于化工、石油、国防、物理、化学、生物工程、医药卫生、生命科学、环境工程、高等院校、科研机构等领域，覆盖了国内近三十个省市、自治区。
公司崇尚"诚信、专业、服务"的企业理念；树立"做一流企业、创知名"的发展目标；贯彻"以市场为导向、以技术为基础、以服务为根本"的经营理念；实现"让用户满意"的服务宗旨；履行"百分之百合格出品精益求精周到服务"的承诺。上海旌派全体员工欢迎各位同行、各位合作之友、各位用户与我们携手共同致力于国家科研仪器的发展，共同追求属于我们的未来。
更新时间：2024/4/16 9:51:14
标签：
冰冻血浆解冻箱干式溶浆机旌派公司生产制造氮吹仪
技术支持：阿仪网， 总访问量：2065291
